SHARK MULTIMEDIA LEOPARD 336 Card Type Modem (asynchronous) Chip Set Rockwell I/O Options Microphone in, speaker out , line in, line out Maximum Modem Rate 33.6Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103/212A ITU-T V.34, V.FC, V.32bis, V.32, V.22bis, V.22, V.23 V.21 Fax Modulation Protocol ITU-T V.17, V.21CH2, V.27ter, V.29 Error Correction/Compression MNP5, V.42bis Fax Class Class I & II Data Bus 16-bit ISA Card Size Half-length, half-height card [Image] CONNECTIONS Function Label Function Label Line out CN1 Microphone CN3 Line in CN2 Speaker out CN4 SUPPORTED COMMAND SET Basic AT Commands AT, A/ A, B, D, E, H, M, O, P, Q, T, V, W, X, Y, Z &D, &M, &P, &Q, &R, &T, &W, &X, &Y, &Z Extended AT Commands \A, \B, \K, \N, %C, %E, %L, %Q S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25, S26, S27, S28, S29, S30, S38, S39, S40, S46, S48, S82, S91, S92, S95 Special Commands -K, +MS Note: See MHI Help File for full command documentation. Proprietary AT Command Set TRANSMIT CARRIER Type: Configuration Format: AT [cmds] Cn [cmds] Description: Controls the transmit carrier switching Note: Disabling the transmit carrier puts the modem in receive-only mode Command Function C1 Return OK message ECHOPLEX Type: Configuration Format: AT [cmds] Fn [cmds] Description: Selects whether commands sent while in data mode are echoed Note: This command is only supported on older modems Command Function F0 Auto detect mode F1 V.21 or Bell 103 F3 V.23 line modulation F4 V.22 or Bell 212A 1200bps line speed F5 V.22bis line modulation F6 V.32bis or V.32 4800 line modulation F7 V.32bis 7200 line modulation F8 V.32bis or V.32 9600 line modulation F9 V.32bis 12000 line modulation F10 V.32bis 14400 line modulation REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports modem model and speed I1 Reports ROM checksum I2 Report OK I3 Report firmware revision, model, and interface type I4 Report response programmed by OEM I5 Report the country code parameter I6 Report modem data pump model and code revision I7 Report DAA code SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting AUTO-MODE DETECTION Type: Configuration Format: AT [cmds] Nn [cmds] Description: Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. Command Function N0 Auto-mode detection disabled N1 Auto-mode detection enabled RLSD Type: Configuration Format: AT [cmds] &Cn [cmds] Description: Selects whether the RLSD option is enabled or disabled Command Function &C0 Force RLSD active regardless of the carrier state &C1 Allow RLSD to follow the carrier state FACTORY DEFAULT PROFILE Type: Configuration Format: AT [cmds] &F [cmds] Description: Sets values in active profile to values found in the default profile Command Function &F0 Restore factory configuration 0 &F1 Restore factory configuration 1 GUARD TONE Type: Configuration Format: AT [cmds] &Gn [cmds] Description: Commands the modem to transmit a guard tone in V.22/V.22bis Note: Used primarily for international data transmission Command Function &G0 Guard tone disabled &G1 Guard tone disabled &G2 1800Hz guard tone enabled JACK TYPE Type: Configuration Format: AT [cmds] &Jn [cmds] Description: Included for compatibility, performs no function. FLOW CONTROL Type: Configuration Format: AT [cmds] &Kn [cmds] Description: Enables flow control options Command Function &K0 Flow control disabled &K3 RTS/CTS flow control enabled &K4 XON/XOFF flow control enabled &K5 Transparent XON/XOFF flow control enabled &K6 RTS/CTS and XON/XOFF flow control enabled LINE TYPE Type: Configuration Format: AT [cmds] &Ln [cmds] Description: Selects line type Command Line Type &L0 Switched line (PSTN/Dial-up) DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR high only while modem is handshaking or connected CONFIGURATION PROFILES Type: Immediate Format: AT [cmds] &V [cmds] Description: Displays active and stored configuration profiles Command Function &V1 Displays the connection statistics Extended AT Commands CONNECT MESSAGE Type: Configuration Format: AT [cmds] \Vn [cmds] Description: Selects extended result codes Command Function \V0 Connect messages are controlled by the command settings X, W, and S95 \V1 Connect messages are displayed in the single line format AUTO-RELIABLE FALLBACK CHARACTER Type: Configuration Format: AT [cmds] %An [cmds] Default: 19 Range: 0-127 Unit: ASCII Description: Sets the character used as the auto-reliable fallback character Command Function %A0 Disable PLUG AND PLAY SERIAL NUMBER Type: Immediate Format: AT [cmds] %7 [cmds] Description: Displays the Plug and Play serial number PLUG AND PLAY VENDOR ID Type: Immediate Format: AT [cmds] %8 [cmds] Description: Displays the Plug and Play vendor ID and product number MNP10 - FALLBACK Type: Configuration Format: AT [cmds] -SECn [cmds] Description: Allows MNP10 to fall back to speeds slower than 4800bps Command Function -SEC0 MNP 10-EC disabled -SEC1 MNP 10-EC enabled and set transmit level 0 to 30 DISTINCTIVE RING Type: Configuration Format: AT [cmds] -SDR=n [cmds] Description: Controls the distinctive ring type Command Function -SDR=0 Disable distinctive ring -SDR=1 Ring type 1 -SDR=2 Ring type 2 -SDR=3 Ring type 1 and 2 -SDR=4 Ring type 3 -SDR=5 Ring type 1 and 3 -SDR=6 Ring type 2 and 3 -SDR=7 Ring type 1, 2, and 3 RPI MODE Type: Configuration Format: AT [cmds] +H [cmds] Description: Sets the flash memory download speed Command Function +H0 RPI/Video Ready Mode disabled +H1 RPI enabled and DTE speed set to 19200kps +H2 RPI enabled and DTE speed set to 38400kps +H3 RPI enabled and DTE speed set to 57600kps +H11 RPI+ mode enabled +H16 Video Ready Mode enabled BLACKLISTED NUMBERS Type: Configuration Format: AT [cmds] *B [cmds] Description: Displays the list of permanently blacklisted numbers DELAYED NUMBERS Type: Configuration Format: AT [cmds] *D [cmds] Description: Displays the list of delayed numbers COUNTRY Type: Configuration Format: AT [cmds] *NCn [cmds] Description: Changes the country to one of eight listed in NVRAM S(status) -REGISTERS BIT-MAPPED REGISTER S19 Format AT [cmds] S19=n [cmds] Default: 0 Range: Unidentified Description: AutoSync options BIT-MAPPED REGISTER S20 Format AT [cmds] S20=n [cmds] Default: 0 Range: 0-255 Unit: Bit-mapped Description: AutoSync HDLC address or BSC Sync character BIT-MAPPED REGISTER S31 Format: AT [cmds] S31=n [cmds] Default: Unidentified Range: 0-10 Description: Select automode and extended result code format. Bit Value Function 0 0 Not used 1 0 Auto-mode detection disabled 1 In originate mode, handshake begins at line speed designated by the S37 register. Modem can shift to a slower speed if necessary. In answer mode, handshake attempted with the following protocols in order - V.FC, V.32bis, V.32, V.22bis, V.22 or Bell 212, V.21, and Bell 103 2-3 0 Auto line speed detection (Nn) disabled 1 Auto line speed detection (Nn) enabled 4-5 0 Caller ID disabled 1 Short Caller ID enabled 2 Long Caller ID enabled 6-7 11b Reserved DCE LINE SPEED Type: Register Format AT [cmds] S37=n [cmds] Description: Sets the maximum allowable data exchange rate attempted during handshake process. Command Function S37=0 Attempt automode connection. If N0 is active, connection is attempted at the most recently sensed DTE speed. If N1 is active, connection is attempted at the highest possible speed. S37=1-3 Attempt to connect at 300bps S37=4 Reserved S37=5 Attempt to connect at 1200bps S37=6 Attempt to connect at 2400bps S37=7 Attempt to connect at V.23 S37=8 Attempt to connect at 4800bps S37=9 Attempt to connect at 9600bps S37=10 Attempt to connect at 12000bps S37=11 Attempt to connect at 14400bps S37=12 Attempt to connect at 7200bps BIT-MAPPED REGISTER S41 Format AT [cmds] S41=n [cmds] Default: Unidentified Range: 0-31 Unit: Bit-mapped Description: Selects compression, auto-retrain, flow control, and MNP mode. Bit Value Function 0-1 0 Disabled 1 MNP5 2 V.42bis 3 MNP5 and V.42bis 2,6 0,0 Retrain and fallback/fall forward disabled 0,1 Retrain enabled 1,0 Fallback/fall forward enabled 3 Reserved 4-5 Reserved 7 Reserved BIT-MAPPED REGISTER S86 Format AT [cmds] S86=n [cmds] Default: Unidentified Range: 0, 4, 5, 9, 12, 13, 14 Unit: Bit-mapped Description: Records the first event that contributes to a NO CARRIER message. Command Function S86=0 Normal disconnect, no error occurred S86=4 Loss of carrier S86=5 V.42 negotiation failed to detect an error-correction modem at the other end S86=9 The modems could not find a common protocol S86=12 Normal disconnect initiated by the remote modem S86=13 Remote modem does not respond after 10 re-transmissions of the same message S86=14 Protocol violation